PDA

View Full Version : OBD-Codes

stanger
Dec 01 2004, 08:06pm
This site is the premier OBD trouble codes resource site.

www.obd-codes.com
Tempe
Feb 23 2005, 02:17pm
This site is the premier OBD trouble codes resource site.

www.obd-codes.com

That site is the premier OBD trouble codes resource site only if it's not a dead link :(
wood_e
Jul 06 2005, 08:32am
2 digit codes: http://www.midwestsho.com/catalog/troubleshooting.php?codes=2digit

3 digit codes: http://www.midwestsho.com/catalog/troubleshooting.php?codes=3digit

Those are for ECC IV systems
rwenzing
Jul 06 2005, 09:05am
This site is the premier OBD trouble codes resource site.

www.obd-codes.comHeads up: For many generic OBD-II codes in this list, the troubleshooting guides say to look for Bank 1 problems on the driver's side. While this may be correct for many brands, it is wrong for Fords. On a Ford, Bank 1 is the passenger's side, Bank 2 is the driver's side.
6pack
Dec 31 2006, 03:18pm
The first link works but is way confusing. The other links seem to be dead. Can anyone point me towards a DTC list for my truck?
rwenzing
Dec 31 2006, 04:31pm
The first link works but is way confusing. The other links seem to be dead. Can anyone point me towards a DTC list for my truck?http://www.troublecodes.net/OBD2/Pcodes.shtml#150

http://home.comcast.net/~miracerros/dtc_powertrain_1.htm

http://home.comcast.net/~miracerros/dtc_powertrain_2.htm
6pack
Dec 31 2006, 04:52pm
That is sweet. They should be in the tech section here so the links never die.
Thanks!
NyghtStalkr
Jan 18 2008, 02:49pm
Hey, question.... P1400 says in the scanner that it is Auxiliary Emission Controls, yet that site says it is this: P1400 Differential Pressure Feedback Electronic Sensor circuit Low Voltage

What is it?
rwenzing
Jan 18 2008, 05:58pm
The DPFE sensor reads the gas flow through the EGR tube and reports it to the PCM as a voltage. The P1400 code says that the DPFE sensor voltage at the PCM is less than 0.2V which is unacceptably low. If there is no other issue such as an unplugged connector or damaged wiring, then the sensor is probably bad.
da bazzman
Feb 02 2008, 01:31am
My 94 B-4000 truck is an old obd 1 [or is it?] and this link didn't do me any good. My reader doesn't give me 'p' codes, ect. So where to now? Fork out for a new reader?
KOEO is just a set of beeps like someone was pre-recording the bass drum track for a disco song, no patterns or breaks to it. Just beep-beep-beep etal.
rwenzing
Feb 02 2008, 07:24am
My 94 B-4000 truck is an old obd 1 [or is it?] and this link didn't do me any good. My reader doesn't give me 'p' codes, ect. So where to now? Fork out for a new reader?
KOEO is just a set of beeps like someone was pre-recording the bass drum track for a disco song, no patterns or breaks to it. Just beep-beep-beep etal.OBD sticky from the top of this subforum.

http://www.rangerpowersports.com/forum/showthread.php?t=222911
da bazzman
Feb 02 2008, 10:31am
The first time I read it I missed how to erase, caught it this time, thanks.